We are looking for Fuel Pumps with the following specs. Kindly give us your best quotes. Our requirements are as follows: 1) FUEL PUMP Portable Fuel Pump Heavy duty Centrifugal fuel pump, diesel driven engine with flow rate of 500 lt/min, mounted on heavy duty two wheeled cart ( suitable for the transfer of diesel) and complete with following: a) Discharge hose 15M x 3.75cm with piston style fuel nozzle b) Meter reading device c) Suction hose 3M by 5.03cm with quick coupler and dust cap d) Filter/separator assembly to remove sediment and water, with five (5) additional replacement filters e) Static ground and bonding cable f) Spark arrestor g) Pressure relief valve and loop (bypass) and gate valve assembly that includes nipple, elbow, valve and 5.03cm male cam lock. 2) Spare parts kit for pump in line item(1) above including air filter, lube, oil filter, fuel filter, seal assembly pump, rol sealing tape, set O-ring gaskets, packing, set hose clamp high pressure ( suction and delivery). 3) Velcon filter Housing VF-61E Features: Maximum operating pressure: 150psl Material: die cast aluminium head and closure clamp assembly carbon steel shell with epoxy coated exterior and interior inlet/outlet connection: 11 by 2 inch NPT Closure seal: Buna-N O-Ring 1/8" Petcock Vent Valve and half inch drain Valve Suitable for jet A1 Aviation Fuel. 4) Filter Cartridge AC-51201L for use with VF-61E Housing Suitable for Jet A1 Aviation fuel. Maximum Operating Temperature: 200 degrees Fahrenheit, Flow rates: 5-50USGPM 5) VF-61E Differential Pressure Gauge Kit for use with the VF-61E Housing Features. Differential Pressure Gauge: Aluminium body, 1 by 8 inch NTP Bottom 1inch molded lens & 0-20 psid Scale. Compression fitting 1 straight another one 90 degrees elbow. 6) Rotary Hand Pump with counter Suitable for handling Gasoline, diesel fuel, light and other non corrosive based fluid from 200 liters drum and equipped with a flow meter/ counter to measure the quantity of fuel in liters. Pump should be equipped with handles, 1inch telescopic steel suction pipe extending to 40inch, 2inch bung adopter, Nozzle, three-quarter inch by 8inch delivery hose with static wire, filter strainer, anti siphoning valve. Pump can be set up to reverse flow and may be padlocked. Other features of the pump are as below: Construction - Aluminium Body with Cast Iron Rate of flow - 3.8Liters per 10 revolutions Maximum ambient operating temperature - 66 degrees Celsius Minimum ambient operating temperature - -26 degrees Celsius Pump must show evidence of approval/certification by a nationally or internationally recognized organization for testing of products to be ensured public safety.

We are looking for 34pict vw beetle carb year 1973. If interested please contact us asap.

our company interested in VW Beetle Aftermarket Performance Parts:Kindly please send me your Quotation for the following parts1- FORGED CHROMOLY COUNTER-WEIGHTED CRANKSHAFT - 74MM - STANDARD VW JOURNAL2- 200MM FLYWHEEL FOR FORGED FLANGED CRANK3- 12 VOLT ELECTRIC FUEL PUMP4- FORGED HIGH-LIFT ROCKER ARMS5- HIGH-REV VALVE SPRING KIT6- ROCKER SHAFT SHIMS 8 PCS7- CHR-MOLY ROCKER STUDS8- HEAVY DUTY OIL PUMP W/ 8MM HOLES9- HI-PERFORMANCE CAMSHAFT10- STRAIGHT CUT CAM GEARS (Steal, Aluminum)11- CAM FOLLOWER- LIFTER RETAINING CLIPS12- HROMOLY BILLET STEEL GLAND NUT W/ WASHER13- CHROME 009 STYLE MECHANICAL ADVANCE DISTRIBUTOR14- Electronic ignition for 00915- Blue Ignition Wires16- Blue CoilYou can also offer a full COMPLETE PERFORMANCE CAM KIT - ALL 1600CC BEETLE STYLE ENGINES - .320 INCH LIFT AT LOBE / 277 DEGREE C20 CAM & GEAR / SINGLE HD VALVE SPRINGS / SCAT LIFTERS / HD RETAINERS & KEEPERS.

We are looking for fuel injector. If interested please contact us free.

We are interested in ignition coil. Please contact us if you have. Thanks in advance.

We are Supply & Services Company in Malayisa. Please quote this inquiry: 32 Pc Spring Valve Part Position : Item Number : 7 Drwg No: KXN-41TS-124 Sub Assembly : Suction Valve Compressor Type : Reciprocating MFR Of Compressor : Kobelco, Japan Compressor MOdel Number : KR30-2 MRC HPU-2 Plant Equipment : Natrual Gas Compressor, K_39403 A/B Mfr : KObelco Tag No.: K-39403 A/B Model :KR 30-2 MFR Serial No: WH-W0013#4 Delivery : 18.05.09 2. 1 PC Gasket KO Drum Part Position / Item Number : 5Drwg No: KXN-41TS-124 Sub Assembly : KO Drum DRWG Number : VP-K-39403A/B V01-001 Compressor Type : Reciprocating MFR Of Compressor : Kobelco, Japan Compressor MOdel Number : KR30-2 MRC HPU-2 Plant Equipment : Natrual Gas Compressor, K-39403 A/B Mfr : KObelco Tag No.: K-39403 A/B Model :KR 30-2 MFR Serial No: WH-W006A#03 Delivery : 18.05.09 Please give me your good price (DDP to Malaysia) weight of goods&dimension, delivery date, warranty and terms of payment a.s.a.p.

we r looking for cly block for cummins 6bt 5.9 eng for india.

Hello. I am inquiring about the camshaft for engine G4ED. I know the listing is for Kia DOHC G4ED. I am using an hyundai DOHC G4ED engine. I read that it is similar. Of course, only experts like you can verify if it is true.If so, I would like to know the cost of the camshafts. I assume it comes as an intake and exhaust camshafts. But what I really need to know is what angle is the shaft? As in, is it for street or purely for race? Because it is going to be very rough on the idle if it is purely for race.Thanks. I am inquiring from Singapore. Thank you very much.

I want to buy Camshaft For Cummins 6BT, please contact us.

We are from target trade in egypt and interested in oil pumps. Please contact us free.