我们目前在做供应商的储备工作，2010年开始采购，需要找转速表的供应商，需要有配套经验。

我们目前在做供应商的储备工作，2010年开始采购，需要找水温表的供应商，需要有配套经验。

我们目前在做供应商的储备工作，2010年开始采购，需要找燃油表的供应商，需要有配套经验。

我们目前在做供应商的储备工作，2010年年末开始采购，需要找机油压力表的供应商，需要有配套经验。

我们需要安全系统的一些汽车零部件供应商做储备，在找汽车仪表板供应商。供应商最好有TS认证，最好有配套经验。

我们有意向储备一批仪表配套供应商，适用于我们的商用车。 供应商要求： 1. TS16949是基本的； 2. 有相关大型商用车整车厂供货经验； 3. 江浙沪优先考虑。

我们有意向储备组合仪表配套供应商。要求： 1. TS16949； 2. 有大型主机厂直接配套经验； 3. 长江一带优先考虑。

我们正在寻找组合仪表配套供应商，具体要求： 1. TS16949是基本的； 2. 有大型主机厂配套经验。

We are looking for Combination Meter for Genset.The specification as follow: Electrical Instrument cluster consisting of – 1.RPM cum Hourmeter – RPM range up to 2200 rpm. The range should have least count of 50 rpm or better. The rpm between 1450-1550 rpm to be indicated in Green color also the rpm between 1750-1850 rpm to be indicated in Green color. RPM should be in analog display of needle, the Hours should be up to 0.1 least count DIGITAL. RPM signal will come from battery charging alternator/main alternator. 2.Water Temperature gage – showing in deg. C. This should show temp up to 120 deg C. Temp above 95 deg C to be indicated in Red color. The least count is not important. But typically should show 50, 60, 70, 80, 90, 100 and 110. However, it should not show any further graduation between these numbers. 3.Oil Temperature gage – same as Water Temp gage. This is optional gage. 4.Pressure gage – Showing pressure in kg/cm2. The pressure range between 0-1 kg/cm2 in Red color. Up to 7 kg/cm2. 5.Battery Voltage – showing voltage up to 28/30 V. 6.Battery Current – showing current up to -30 to +30 Amps, least count of 5 Amps. 7.Fuel level gage – showing the fuel level as Empty to Full, with graduation for 1/10th level as least count. 8.Fault Indication for the following required – a.Oil pressure low b.Water Temp high c.Battery charging failure with excitation for battery charging alternator d.Over speeding trip e.Fuel Level at or below 10% f.Emergency Stop activated g.Additional 1-2 lamps

我们有意向为新开发车型寻找带CAN的行驶记录仪配套供应商，预计8月份开始采购，车型类似于江铃全顺那一款商用车。 对供应商要求： 1. 必须有给上汽集团，长安福特，上海大众，江铃之类的整车厂配套经验（乘用车配套经验也可）； 2. 中型或大型生产厂； 3.至少有ISO9001认证，TS14949优先考虑。 4. 有无出口经验，地理位置都不重要，关键是有能力生产。